underbelly sheetmetal coming off

These are discussions that contain lots of good info, so did not want to eliminate it. It has closed so we can take advantage of making the forum easier to find what you are looking for.

underbelly sheetmetal coming off

Postby jerry » Sun Dec 16, 2007 3:12 pm

Just got back from short weekend trip and while returning home our friends behind us noticed some insulation fall from underneath my bird. I stopped and found one strip of sheetmetal peeling back allowing the insulation to blow out. I noticed several screws either gone or coming out.
Does anyone know of a good way to put in new sheetmetal screws and make them stay. Not long ago I got under the bird and tightened up every screw that appeared to be coming loose. Most of these screws do not screw into anything solid, just the other piece of sheetmetal.

Thanks, Jerry

2006 Cardinal 30WBLE
2003 Ford PS
Posts: 37
Joined: Tue Jun 13, 2006 6:20 pm
Location: Texas West Columbia

Postby Future Fulltimers » Sun Dec 16, 2007 3:31 pm

Try putting some calking around each hole and on the screw threads before reinstalling the screw. This should keep the screw from vibrating loose. I would use silicone since it will stick to just about anything.
Wayne & Peggy Williamson
GoodSam Lifetime Members
2006 30TS
2007 Silverado 3500 Classic 6.6L D'Max
AirSafe 25k hitch
User avatar
Future Fulltimers
Posts: 848
Joined: Thu Mar 16, 2006 5:35 pm
Location: Tennessee Eastern (Deceased)

Postby Tim » Sun Dec 16, 2007 5:01 pm

Also recommend you go up one sheet metal screw size when you make the repairs.

Postby Olbird » Sun Dec 16, 2007 5:59 pm

They make screws with serrated heads that grip into the sheet metal like a locking star washer does but its made onto the screw.
I used the serrated screws on all the frame backed areas, and used hollow back folding pop rivets made from Aluminum for all areas that are sheet metal to sheet metal attachment. If I have to remove a panel I will just drill them out.
George & Julie
2014 3850 RL Full Paint w/ TrailAir Spring Ride System, Kodiak Disc Brakes, TrailAir Tri-Glide Pin Box, Over 130 Mods

GMC 3500 Denali DRW
User avatar
Council, Asst. Admin
Posts: 3996
Joined: Fri Mar 10, 2006 9:29 pm
Location: Washington, LaCenter

Postby Shields » Sun Dec 16, 2007 8:19 pm

I rescrewed mine down last year, after one trip half of them were missing. And I went up one size in screws. However, all that did was make a larger hole and many are missing again. I am going to the pop rivet route also, but I sure wonder how many flat tires were behind me. :(
Al and Nadine
Cardinal 31RK, 2006
2009 Dodge Cummins 3500 Dually.
Dorr, Michigan
User avatar
Posts: 443
Joined: Thu Mar 23, 2006 9:18 pm
Location: Michigan Dorr

Postby markj » Mon Dec 17, 2007 11:45 am

A couple months ago I noticed the same thing under mine--several screws loose or gone. I got some silicone especially for aluminum and pumped a good amount of it in each hole and rescrewed the screws back in. I bought several of the same size--they worked ok, one size up probably would have been better, but either way the silicone has held them fine!
2007 Cardinal 31RKLE
Hijacker 21K underfloor mount
Fifth Airborne pin box
2006 Ford F350 PSD extended cab
1990 Seaswirl fishing boat!
Kiki (the cat)
Posts: 325
Joined: Thu Feb 01, 2007 1:30 pm
Location: Washington Burlington

Postby Wadcutter » Mon Dec 17, 2007 7:00 pm

I had the same problem after I hit a racoon that ran out in front of us. You could see where he bounced up against the sheet just behind the axle. I did a sure fix. Took a 1"X3" and cut it to fit between the frame rails inside the belly. Then calked it good using silicone caulk where the sheets overlap. Used 1-1/2" X 1/4" galvanized lag bolts every 8" so they went thru both sheets of metal and into the 1"X3".
Don't forget to replace your insulation before screwing the sheets back together.
Posts: 43
Joined: Thu May 18, 2006 4:44 am
Location: Illinois Central,

Sheet metal screws coming off

Postby tug911 » Tue Dec 18, 2007 6:30 am

I found several of mine loose and I just used some over sized rivets to hold them in place. If you need to access that spot then just drill out the rivet.

Postby Bob and Renate » Thu Jan 31, 2008 6:00 pm

I almost lost a panel on my 2004 29WBLE. I drilled new holes and refastened the panels with a # 10 sheet metal Phillips screw. The way it should be done is drill the outer hole larger, (clearance for the screw body) and size the hole you fasten the screw to the same size as the screw core. Almost all sheet metal fabrication is done the way our panels are installed. Either by using a “drill screw” or using the same size bit for both holes. It is cheep and economic, but the mechanical strength is compromised. By tightening the screw this way the thin sheet metal is easily stripped, without noticing it.
It really works better the old fashion way.


Bob and Renate
2012 Cardinal 3550RL, LX & Red Bird Pkg. and more
2011 F350 6.7 Diesel Lariat, FX4 off road, long box,
User avatar
Bob and Renate
Posts: 236
Joined: Fri Jan 11, 2008 2:59 pm
Location: California Santa Rosa

Return to Closed Miscellaneous Discussions

Who is online

Users browsing this forum: No registered users and 1 guest